Can you drive a forklift over any type of surface?

You can drive a lift truck over any type of surface.

Is it safe to drive a forklift backwards?

Use extreme caution when backing up. Potential Hazards: While backing up or reversing, be aware of these potential hazards: Pedestrians being struck by or crushed by the forklift.

Can a forklift tip over without a load?

Forklift Safety Rule Two: Don’t tip over. Many untrained operators assume that they can drive faster without a load, but look at the location of the CG with unloaded forks. … On the other hand a loaded forklift is more likely to tip forward with the CG now closer to the front axle.

How should you normally drive your forklift?

Always operate the forklift at a speed that will allow you to stop it in a safe manner. Slow down when driving on wet or slippery floors. If the load you’re carrying obstructs your forward view, travel with the load trailing instead.

IT IS INTERESTING:  What is VNA forklift?

What should you do if the forklift tips over?

If the forklift is tipping over, protect yourself by staying put: Stay in your seat and do not attempt to jump off. Lean away from the falling direction of the lift. Hold onto the steering wheel and make sure you’re stable.

When should you drive backwards on a forklift?

“Drive backwards if the load obstructs your forward view; but use a rotating seat if you have one. Otherwise the frequent twisting will put excessive strain on your spine.” That, in brief, is the recommendation set out for drivers and operators.

Why are forklifts so dangerous?

There are many factors that explain why forklifts are dangerous: Forklifts are heavy. … The weight of a forklift is unevenly distributed, which makes it harder to operate and drive. The rear wheels of a forklift are responsible for turning the vehicle, increasing the chances of tipping during tight turns.

Where can you not park a forklift?

Do not park the forklift in a location with its fork arms protruding the passageway, where there are a lot of pedestrians who will have to step over them. Do not leave the truck in any access doorways and it should not block any stairways of the workplace. Never leave the truck near first aid stations.

What is the first thing you need to do before raising or lowering a load?

Ensure the load is secured before moving. Slowly move the truck to 20 to 30 cm (8 to 12 inches) away from the stack. Stop the truck. Return the mast to the vertical position before lowering the load.

IT IS INTERESTING:  How long does it take to get forklift certified?

Why do forklifts not tip over?

At the back of every forklift is a counterweight. The size of this counterweight will depend on the capacity of the forklift. … The counterweight acts as a balance for the weight being lifted by the truck’s forks. As long as the center of gravity is inside the wheelbase for the vehicle, the forklift won’t tip over.

Why are there 3 pedals on a forklift?

To begin with, every forklift comes equipped with an accelerator and a brake pedal. That third pedal is called an Inching Brake. Its function is twofold. It initially acts as a brake and secondly disengages the transmission, allowing the engine speed to increase or decrease without affecting the drive of the forklift.

Is forklift driving hard?

It is not hard to drive a forklift. But to be a skilled forklift driver takes a lot of practice. … It is not hard to drive a forklift. But to be a skilled forklift driver takes a lot of practice.

How high should your forks be when driving forklift?

Keep the forks 6 to 10 inches above the ground to avoid potential hazards on the ground. Remember that forklifts are top-heavy. Carry the load low and tilted back.

What is the maximum safe speed for a forklift?

The Material Handling Equipment Distributors Association (MHEDA) recommends a max speed of 8 mph in general and a 3 mph max speed in areas where pedestrians are present.

How can a forklift be overturned?

WHAT CAUSES FORKLIFT OVERTURNS? — Turning, stopping or pushing the go pedal too quickly. — Driving on an incline. — An unbalanced load, driving with a load too high or a load too heavy for the equipment.

IT IS INTERESTING:  How heavy is a forklift propane tank?

When picking up a load the correct fork spacing should be?

Answer: When picking up a load the correct fork spacing should be 6 inches and also the forks must be spaced as wide apart as necessary for the maximum support of the load.

Efficiency