How do you carry a load on a forklift?

Keep the forks 6 to 10 inches above the ground to avoid potential hazards on the ground. Remember that forklifts are top-heavy. Carry the load low and tilted back. Use caution when carrying a load on an uneven surface; it creates a tip-over hazard.

Can you strap a load to a forklift?

Secure a forklift load, so it will remain in place at all times. Avoid picking up damaged loads unless they have been secured by wrapping or banding. … Do not exceed the load capacity of your forklift.

Where should loads be located on forklifts?

Keep the center of gravity of the load as low to the ground and as close to the front wheels as possible: Carry the load at the lowest position possible, 4 to 6 inches from the ground. Tilt the mast back and position the heaviest part of the load against the carriage.

IT IS INTERESTING:  What kind of oil does a Yale forklift take?

What is the best way to handle an uneven load?

Tilt the load against the backrest. If the load is unstable, lift the load slightly first, then carefully tilt it back so that the load stays tight against the backrest. If it’s a stable load and secure on the pallet, tilt first, then lift. Once the load is lifted, lower it to a safe traveling height.

When traveling with a load the load should be lifted 5 inches?

once you are clear, stop the forklift and lower the forks as far as possible. On a flat floor, lower them until they are 2 to 5 inches above the floor. On rough terrain, lift the forks higher to accommodate uneven ground.

When picking up a load the correct fork spacing should be?

Answer: When picking up a load the correct fork spacing should be 6 inches and also the forks must be spaced as wide apart as necessary for the maximum support of the load.

What will make the load more stable during travel?

When traveling with a load, always make sure to tilt the mast of the forklift backward so that the load will firmly place against the backrest to make it more secure during transport. By doing this, you move the center of gravity towards to rear of the forklift making it more secure when traveling.

What should you check before lifting a load?

Requirements and Recommended Practices:

  1. Check that there is adequate overhead clearance before raising the load. …
  2. Carefully lift the load up above the lower stack about 10 cm (4 inches). …
  3. Lift the load clear and then tilt the mast back slightly to rest the load against the load backrest extension.
IT IS INTERESTING:  How much does a lift truck cost?

What is the load Centre distance on a forklift?

A load center is the horizontal distance from the vertical face of the forks to the center of gravity of the load. As a general rule, load center is 24″ from the face of the forks (the center point of standard 48” x 48” pallet). Forklift capacities range from about 3,000 lbs up to more than 70,000+ lbs.

How much can a 5000 lb forklift lift?

A 5,000-lb. capacity forklift will lift that much weight up to 48-inch forks (with a 24-inch load center) but going out to 60 inches (with a 30-inch load center), for example, drops the capacity to 4,000 pounds.

What happens to the center of gravity when you lift a heavy load above the forklift?

Heavier loads shift the center of gravity forward even further. Raising the load also shifts the center of gravity forward. In order to prevent the lift from tipping, the combined center of gravity of the load and the lift must stay inside the stability triangle (at ground level) at all times.

How much back tilt is required when transporting a palletised load?

Apply sufficient back tilt to cater for the type of load and ground conditions when transporting a palletised load. Never use the full range of tilt with the forks raised laden or un-laden (100-150mmm).

What steps should you do every time you park a forklift?

  • Select an area to park. Do not park in an unauthorized area. Do not block an aisle or exits. Follow your company’s parking procedures.
  • Apply brake slowly and stop.
  • Neutralize the controls.
  • Set the parking brake.
  • Turn off the ignition.
  • If the truck is parked on an incline, block the wheels.
IT IS INTERESTING:  Does lifting a truck add value?

Where on the forks should you try to keep the heaviest part of an unbalanced load?

If the load is unbalanced, keep the heavier end closer to you. Tilt the mast back. Lift the load and tilt it back a little more before traveling. Keep the forks 6 to 10 inches above the ground to avoid potential hazards on the ground.

What happens when the load Centre is increased?

The weight capacity of a forklift attachment is tied to what is known as the Maximum Load Moment, which is when the load center distance increases, changing the weight distribution, and as a result, the amount of weight a truck can carry under those conditions.

Efficiency