Question: What is forklift nameplate?

The nameplate (also called the data plate) provides important information for the forklift operator, including the fuel type, forklift weight, and capacity. Operators should read the nameplate to know the forklift’s capabilities and limitations.

What information is found on a forklift load plate?

The data in the table specifies important information regarding the forklifts load handling capabilities: Load Height is the maximum height the forklift mast can lift a load. Maximum Capacity Mast Vertical is the maximum weight the forklift can lift when the mast is extended to its full height.

What is a capacity plate on a forklift?

According to the Occupational Safety & Health Administration (OSHA), a standard forklift capacity plate is a nameplate that contains the capacity of the lift truck, where the capacity is defined as “the manufacturer’s guideline for how much weight a forklift can safely lift.”1 The nameplate contains a host of …

IT IS INTERESTING:  You asked: Can I lift my truck with just shocks?

Do forklifts have license plates?

OSHA Does State Nameplate Requirement on Forklift

29 CFR 1910.178(a)(3) says that forklifts shall include identifying mark or data plate as approval by the testing body (which is in this case, the manufacturer or engineering firm). American National Standard for Powered Industrial Trucks, Part II, ANSI B56.

What are the 3 most important pieces of information found on a capacity plate?

This plate displays three important items:

  • The maximum persons capacity (XX persons or XXX pounds).
  • The maximum carrying weight – persons, motor & gear (pounds).
  • The maximum horsepower recommended for the boat.

Where is the data plate located on a forklift?

The forklift data plate can be found on the instrument panel near the operating controls. It is the responsibility of the operator to understand the capabilities of each forklift and to properly maintain the data plate to ensure it is legible and complete.

How is forklift capacity calculated?

A couple of simple calculations are all that’s necessary:

  1. Divide the load center as stated on the data plate by the actual load center (in the example above, that would be 24/36=. 6666).
  2. Multiply this result by the rated load capacity (4000X. 6666=2666.6).

5 мар. 2013 г.

What is the center of gravity on a forklift?

Center of gravity means the point on an object at which all of the object’s weight is concentrated and all of the parts balance each other. For symmetrical loads, the center of gravity is at the middle of the load in terms of the load’s length, width and height. (Figure 10).

IT IS INTERESTING:  How are crane lift plans calculated?

What is the maximum weight a forklift can carry?

Forklift capacities range from about 3,000 lbs up to more than 70,000+ lbs. You can find the rated capacity of a forklift on its data plate. OSHA requires “only loads within the rated capacity of a truck shall be handled.” It’s easy to think the rated capacity is the same as maximum capacity, but it’s not that simple.

What is plugging on a forklift?

Forklift plugging is common practice that should be encouraged for its benefit of reducing brake wear. Plugging, also called regenerative braking, regen or switch-back, occurs when an operator traveling in one direction uses the directional selector to switch to the opposite direction. …

How do you lift a forklift?

Use a hydraulic jack to raise the steer wheels. Put the jack under the steer axle and frame to raise the lift truck. Make sure that the jack has a capacity of at least 2/3 of the lift truck total weight as shown on the capacity plate. Place blocks under the frame and counterweight to support the lift truck.

How heavy is a fork lift?

How Heavy Is a Forklift? The average weight of a forklift is roughly 9,000 lbs. Comparatively, the average automobile weighs about 3,000 lbs. A forklift tends to be heavier in the rear, too.

When picking up a load the correct fork spacing should be?

Answer: When picking up a load the correct fork spacing should be 6 inches and also the forks must be spaced as wide apart as necessary for the maximum support of the load.

IT IS INTERESTING:  What type of equipment is a forklift?

Why should a boats gas tank never be completely filled?

It’s important to never fill the tank of your boat beyond 90% full. This leaves room for gas to expand and avoids the potential for overflow. … After you’re done fueling, tightly replace the gas cap. This will prevent the escape of fuel vapors.

How can you prevent static sparks while filling your boat’s fuel tank?

While filling the fuel tank:

  1. Keep the nozzle of the fuel-pump hose in solid contact with the tank opening to prevent producing a static spark.
  2. Use caution and fill the tank slowly to avoid spilling fuel into the boat’s bilge or into the water. …
  3. Never fill a tank to the brim—leave room for fuel to expand.

What happens if a boat is loaded beyond its capacity?

A boat operator should never take a boat on the water with too many people or too much gear on board. Boats loaded beyond their capacity will swamp or capsize more easily and will be more difficult to control.

Efficiency