What must be done daily before using a forklift?

OSHA requires that all forklifts be examined at least daily before they are used to ensure that they’re in safe operating condition. If forklifts are used on a round-the-clock basis, then they must be examined after each shift.

What should I check before operating a forklift?

Second, the operator walks to either side of the forklift—checks the tires, making sure there are no gouges, tears, or imbedded metal, and that there is proper inflation; checks lug nuts; makes sure the axle is greased; checks the overhead guard, and sees that there is no debris lodged behind the mast.

What are 3 fluid levels that need to be checked before using the forklift?

Therefore, before you can use your forklift for operations ensure you check the brake fluids, hydraulic fluids, and the engine oil levels. If they do not match the recommended levels ensure they are properly replenished.

IT IS INTERESTING:  Frequent question: Where is the mast number on a Toyota forklift?

What is the first thing to do before driving a forklift into a trailer?

Before driving your forklift into a trailer, you should chock the trailer wheels, support the nose of the trailer, inspect the dock plate, and check the trailer floor (all of these).

Who is responsible for performing a pre startup daily inspection of the forklift?

Figure 9. Operator ensuring that the operator manual is on board the forklift and legible. The operator should conduct a pre-start visual check with the key off and then perform an operational check with the engine running.

What is the most common type of forklift?

The most popular forklift types on the market today are:

  • Counterbalance Forklift.
  • Telehandler.
  • Industrial Forklift.
  • Rough Terrain Forklift.
  • Pallet Jack.
  • Walkie Stacker.
  • Order Picker.
  • Reach Fork Truck.

10 сент. 2018 г.

What is a safe speed for a forklift?

The Material Handling Equipment Distributors Association (MHEDA) recommends a max speed of 8 mph in general and a 3 mph max speed in areas where pedestrians are present.

What steps should you do every time you park a forklift?

  • Select an area to park. Do not park in an unauthorized area. Do not block an aisle or exits. Follow your company’s parking procedures.
  • Apply brake slowly and stop.
  • Neutralize the controls.
  • Set the parking brake.
  • Turn off the ignition.
  • If the truck is parked on an incline, block the wheels.

What are two guards fitted to a forklift?

The overhead guard is intended for protection while an operator is within the confines of the seat. Also, operators are prohibited from operating forklifts with their hands, arms, feet, legs or any other body parts around the overhead guard supports or while outside the overhead guard.

IT IS INTERESTING:  Frequent question: Can you drive a forklift without a driver's license in NSW?

How much back tilt should be applied when picking up a load?

Carry the load at the lowest position possible, 4 to 6 inches from the ground. Tilt the mast back and position the heaviest part of the load against the carriage.

Who has the right away on a forklift?

OSHA states the pedestrian has the right of way; therefore, operators must be on constant alert. The forklift operator is required to slow down and sound their horn at doorways, intersections, blind spots and when entering or exiting a building.

What is the best way to handle an uneven load?

Tilt the load against the backrest. If the load is unstable, lift the load slightly first, then carefully tilt it back so that the load stays tight against the backrest. If it’s a stable load and secure on the pallet, tilt first, then lift. Once the load is lifted, lower it to a safe traveling height.

How often should operators inspect their forklift?

Federal OSHA requires that forklift vehicles have to be inspected at least daily, or after each shift when used around the clock. You will find this requirement in the Powered Industrial Truck standard at 1910.178(q)(7).

What makes a good forklift driver?

A truly efficient forklift driver has an ability to convey and disseminate data to all pertinent parties. Whether this be tackling the assignment itself, identifying hazards, or boosting morale, advanced communication skills are an essential trait and characteristic for any forklift driver looking to get the job done.

How long should you keep forklift inspection records?

(Note: Cal/OSHA regulations require that daily forklift inspection records be retained for at least one year.) Your forklift checklist should guide you through what you need to visually check and what needs to be checked operationally.

IT IS INTERESTING:  How do you read a forklift plate?

What are the main points of the visual inspection key off )?

What should an operator inspect during the visual pre-use check?

  • General condition and cleanliness.
  • Floor – clear of objects that could cause an incident.
  • Overhead – no obstructions.
  • Nearby objects to avoid as you drive away.
  • Fire extinguisher – present and charged.
Efficiency