What should the operator do before driving a lift truck into a trailer?

Before driving your forklift into a trailer, you should chock the trailer wheels, support the nose of the trailer, inspect the dock plate, and check the trailer floor (all of these).

Can you drive a forklift into a trailer?

Do not drive the forklift into the truck until the bridge or dock plate has been attached. Do not drive the forklift into a truck bed or onto a trailer that has “soft” or loose decking or other unstable flooring. Drive straight across the bridge plates when entering or exiting the trailer.

What steps must be done daily before using a forklift?

1) Conducting a visual check

OSHA requires that all forklifts be examined at least daily before they are used to ensure that they’re in safe operating condition. If forklifts are used on a round-the-clock basis, then they must be examined after each shift.

What should you check before lifting a load?

Requirements and Recommended Practices:

  1. Check that there is adequate overhead clearance before raising the load. …
  2. Carefully lift the load up above the lower stack about 10 cm (4 inches). …
  3. Lift the load clear and then tilt the mast back slightly to rest the load against the load backrest extension.
IT IS INTERESTING:  Where can I not park a forklift?

Can you drive a forklift on a flatbed trailer?

And obviously, a forklift should never be driven onto a flatbed trailer: for tips on flatbed trailer safety and securement, we have a whole separate lesson. Loading a trailer with a forklift should be a safe endeavor. Training your employees will help ensure that it will be.

What are 3 fluid levels that need to be checked before using the forklift?

Therefore, before you can use your forklift for operations ensure you check the brake fluids, hydraulic fluids, and the engine oil levels. If they do not match the recommended levels ensure they are properly replenished.

Which steps should you do every time you park a forklift?

  1. Select an area to park. Do not park in an unauthorized area. Do not block an aisle or exits. Follow your company’s parking procedures.
  2. Apply brake slowly and stop.
  3. Neutralize the controls.
  4. Set the parking brake.
  5. Turn off the ignition.
  6. If the truck is parked on an incline, block the wheels.

How much back tilt should be applied when picking up a load?

Carry the load at the lowest position possible, 4 to 6 inches from the ground. Tilt the mast back and position the heaviest part of the load against the carriage.

What are the 4 steps in safe lifting?

Proper Lifting Technique

  1. Keep a wide base of support. …
  2. Squat down, bending at the hips and knees only. …
  3. Keep good posture. …
  4. Slowly lift by straightening your hips and knees (not your back). …
  5. Hold the load as close to your body as possible, at the level of your belly button.
  6. Use your feet to change direction, taking small steps.
IT IS INTERESTING:  Can you use diesel forklift indoors?

What are the six stages of the safe lifting techniques?

Page 1

  • Identify the object, plan ahead • Where do you need to take the load? • …
  • 2 Holding. the object • Make a decision on how and where to hold the object. …
  • 3 Posture. • …
  • 4 Lifting. • …
  • 5 Walking. with a load • Keep the load as close to your body as possible with your arms straight. …
  • 6 Unloading. •

What will make the load more stable during travel?

When traveling with a load, always make sure to tilt the mast of the forklift backward so that the load will firmly place against the backrest to make it more secure during transport. By doing this, you move the center of gravity towards to rear of the forklift making it more secure when traveling.

Is forklift driving hard?

It is not hard to drive a forklift. But to be a skilled forklift driver takes a lot of practice. … It is not hard to drive a forklift. But to be a skilled forklift driver takes a lot of practice.

Can you fail a forklift test?

Forklift operator practical test penalties

There is for the written test but not for the practical. In fact it’s very simple. … After the test they get added up by the instructor and the total must not exceed 40. If a trainee scores 41 or more they are deemed to have failed the test.

Why do forklifts have 3 pedals?

To begin with, every forklift comes equipped with an accelerator and a brake pedal. That third pedal is called an Inching Brake. Its function is twofold. It initially acts as a brake and secondly disengages the transmission, allowing the engine speed to increase or decrease without affecting the drive of the forklift.

IT IS INTERESTING:  What is a reach forklift truck?
Efficiency