Where is the data plate located on a forklift?

The forklift data plate can be found on the instrument panel near the operating controls. It is the responsibility of the operator to understand the capabilities of each forklift and to properly maintain the data plate to ensure it is legible and complete.

What information is on a forklift data plate?

The nameplate (also called the data plate) provides important information for the forklift operator, including the fuel type, forklift weight, and capacity. Operators should read the nameplate to know the forklift’s capabilities and limitations.

Do forklifts have license plates?

OSHA Does State Nameplate Requirement on Forklift

29 CFR 1910.178(a)(3) says that forklifts shall include identifying mark or data plate as approval by the testing body (which is in this case, the manufacturer or engineering firm). American National Standard for Powered Industrial Trucks, Part II, ANSI B56.

IT IS INTERESTING:  Which of the following persons is responsible for watching pedestrians while operating a forklift?

What are the 3 most important pieces of information found on a capacity plate?

This plate displays three important items:

  • The maximum persons capacity (XX persons or XXX pounds).
  • The maximum carrying weight – persons, motor & gear (pounds).
  • The maximum horsepower recommended for the boat.

What information is provided on the lift truck capacity plate?

Sometimes referred to as a capacity plate or a forklift nameplate, the forklift data plate includes important information such as weight, fuel type, and forklift load capacity. Associates need to read the data plate during training and before use to help build the culture of safety in your facility.

What precautions must be taken to prevent carbon monoxide buildup in forklift areas?

OSHA recommends that employers take the following precautions to reduce the potential for CO exposure in the workplace:

  • Install an effective ventilation system.
  • Maintain appliances in good working order. …
  • Prohibit altogether the use of gasoline-powered tools or engines in enclosed areas.

16 дек. 2013 г.

Which steps must be done at least daily before using a forklift?

1) Conducting a visual check

OSHA requires that all forklifts be examined at least daily before they are used to ensure that they’re in safe operating condition. If forklifts are used on a round-the-clock basis, then they must be examined after each shift.

Is a forklift a motor vehicle?

Yes, it’s true. No dice insurers, a forklift is a motor vehicle. …

When setting a load What should you do first?

Requirements and Recommended Practices:

  1. Check that there is adequate overhead clearance before raising the load. …
  2. Carefully lift the load up above the lower stack about 10 cm (4 inches). …
  3. Lift the load clear and then tilt the mast back slightly to rest the load against the load backrest extension.
IT IS INTERESTING:  Quick Answer: Can you dig with a front end loader?

What is the center of gravity on a forklift?

Center of gravity means the point on an object at which all of the object’s weight is concentrated and all of the parts balance each other. For symmetrical loads, the center of gravity is at the middle of the load in terms of the load’s length, width and height. (Figure 10).

What info is on a capacity plate?

Look for a capacity plate near the operator’s position or on the transom of the boat. This plate indicates the maximum weight capacity and/or the maximum number of people that the boat can carry safely in good weather. You should not exceed either the stated maximum weight capacity or the maximum number of people.

What does a capacity plate indicate?

A Boat’s Capacity

Always check the capacity plate usually near the operators position or on the boats transom. This plate indicates the maximum weight capacity or the maximum number of people that the boat can safely carry.

What is a capacity plate on a forklift?

According to the Occupational Safety & Health Administration (OSHA), a standard forklift capacity plate is a nameplate that contains the capacity of the lift truck, where the capacity is defined as “the manufacturer’s guideline for how much weight a forklift can safely lift.”1 The nameplate contains a host of …

When picking up a load the correct fork spacing should be?

Answer: When picking up a load the correct fork spacing should be 6 inches and also the forks must be spaced as wide apart as necessary for the maximum support of the load.

IT IS INTERESTING:  When should you use plugging to stop the lift truck?

What is a load plate?

The Plate Bearing Test (or Plate Loading Test) is an insitu load bearing test of soil used for determining the ultimate bearing capacity of the ground and the likely settlement under a given load. … The Plate Bearing Test is normally carried out at foundation level, either on the surface or in a shallow pit.

How much back tilt is required when transporting a palletised load?

Apply sufficient back tilt to cater for the type of load and ground conditions when transporting a palletised load. Never use the full range of tilt with the forks raised laden or un-laden (100-150mmm).

Efficiency