Your question: What information is provided on the lift truck capacity plate?

Sometimes referred to as a capacity plate or a forklift nameplate, the forklift data plate includes important information such as weight, fuel type, and forklift load capacity. Associates need to read the data plate during training and before use to help build the culture of safety in your facility.

What information is required on the lift truck data plate?

The data plate includes vital information about the forklift, such as its fuel type, weight, and forklift load capacity. To ensure safe usage of your forklifts, it is necessary to have employees read the data plate thoroughly during training and before use.

What information is on a forklift data plate?

The nameplate (also called the data plate) provides important information for the forklift operator, including the fuel type, forklift weight, and capacity. Operators should read the nameplate to know the forklift’s capabilities and limitations.

IT IS INTERESTING:  What is the OSHA standard for forklift?

What are the 3 most important pieces of information found on a capacity plate?

This plate displays three important items:

  • The maximum persons capacity (XX persons or XXX pounds).
  • The maximum carrying weight – persons, motor & gear (pounds).
  • The maximum horsepower recommended for the boat.

What is a capacity plate on a forklift?

According to the Occupational Safety & Health Administration (OSHA), a standard forklift capacity plate is a nameplate that contains the capacity of the lift truck, where the capacity is defined as “the manufacturer’s guideline for how much weight a forklift can safely lift.”1 The nameplate contains a host of …

Why should a lift truck not be turned on a ramp?

Accidents can happen if you make sudden on-the-go directional changes or attempt to turn a forklift on a grade or ramp. This can happen whether the truck is empty or carrying a load. Sudden directional changes can create an imbalance in the forklift, which can result in a tip-over.

When setting a load What should you do first?

Requirements and Recommended Practices:

  1. Check that there is adequate overhead clearance before raising the load. …
  2. Carefully lift the load up above the lower stack about 10 cm (4 inches). …
  3. Lift the load clear and then tilt the mast back slightly to rest the load against the load backrest extension.

Where is the data plate located on a forklift?

The forklift data plate can be found on the instrument panel near the operating controls. It is the responsibility of the operator to understand the capabilities of each forklift and to properly maintain the data plate to ensure it is legible and complete.

IT IS INTERESTING:  Can you leave a forklift running unattended?

What boats must have a capacity plate?

Federal law requires single-hull boats less than 20 feet in length to have a capacity plate. (However, PWC and sailboat manufacturers are not required to attach a capacity plate.) Always follow the recommended capacity found in the owner’s manual and on the manufacturer’s warning decal.

What precautions must be taken to prevent carbon monoxide buildup in forklift areas?

OSHA recommends that employers take the following precautions to reduce the potential for CO exposure in the workplace:

  • Install an effective ventilation system.
  • Maintain appliances in good working order. …
  • Prohibit altogether the use of gasoline-powered tools or engines in enclosed areas.

16 дек. 2013 г.

What does a capacity plate indicate?

A Boat’s Capacity

Always check the capacity plate usually near the operators position or on the boats transom. This plate indicates the maximum weight capacity or the maximum number of people that the boat can safely carry.

Why should a boats gas tank never be completely filled?

It’s important to never fill the tank of your boat beyond 90% full. This leaves room for gas to expand and avoids the potential for overflow. … After you’re done fueling, tightly replace the gas cap. This will prevent the escape of fuel vapors.

What is the best way to approach a dock when there is strong wind or current?

Answer Expert Verified. the best way to approach a dock when there is strong wind or current is we should approach the dock at a 20-30 degree angle. By doing this, we could secure a bow line, put the engine in reverse toward the dock, and bring stern into the dock.

IT IS INTERESTING:  Quick Answer: How long does it take to put a 6 inch lift on a truck?

When picking up a load the correct fork spacing should be?

Answer: When picking up a load the correct fork spacing should be 6 inches and also the forks must be spaced as wide apart as necessary for the maximum support of the load.

How is forklift capacity calculated?

A couple of simple calculations are all that’s necessary:

  1. Divide the load center as stated on the data plate by the actual load center (in the example above, that would be 24/36=. 6666).
  2. Multiply this result by the rated load capacity (4000X. 6666=2666.6).

5 мар. 2013 г.

What is the best way to handle an uneven load?

Tilt the load against the backrest. If the load is unstable, lift the load slightly first, then carefully tilt it back so that the load stays tight against the backrest. If it’s a stable load and secure on the pallet, tilt first, then lift. Once the load is lifted, lower it to a safe traveling height.

Efficiency